DuPont de Nemours, Inc. · NYSE:DD

DuPont de Nemours — DuPont — Technical Presentation (May 2011)

16 slides from DuPont de Nemours's technical presentation, May 2011

  1. Slide 1: Material Solutions – Turbo, EGR System

    1 Material Solutions – Turbo, EGR System m & anc l st ca e si mi re Re h e tu C ra pe Te

  2. Slide 2: TC System – With Recycle Streams Highlighted

    2 TC System – With Recycle Streams Highlighted Intercooler Exhaust Fresh Air Inlet manifold EGR system PCV system Air filter Exhaust manifold Turbo charger

  3. Slide 3: Approximate Heat Rating of Elastomers, Fibers and Plastics

    OPIS JOH 2PIS PIOD 3 Approximate Heat Rating of Elastomers, Fibers and Plastics FKM — Viton® Meta-aramid VMQ - Silicone Nomex® PPA Zytel® HTN Zytel® Plus PA66 Zytel® PA6 Zytel® 175 AEM-HT - Vamac® 160 AEM — Vamac® 150 Polyester TPC-ET Hytrel® 12 Oo TPV EPDM/PP 6 QO A l = 0) {e) no] x (0) > i) ; 0 El

  4. Slide 4: Chemical Cocktail Resistance

    4 Chemical Cocktail Resistance Previous Automotive Requirements for TC Materials • Hot Air – good heat resistance required • Oil resistance required Requirement Changes as Result of Recycle Streams • Fuel and Oil from PCV system • Acid condensate from EGR and PCV system Laboratory Testing Parameters

  5. Slide 5: Acid Condensate – CPE

    5 Acid Condensate – CPE Tested: 1 week at 90°C in acid condensate from European OEM • pH of about 3 • based on organic acids Tensile bar at end of test. Could not run physicals.

  6. Slide 6: FKM and ECO in Acid Condensate

    6 FKM and ECO in Acid Condensate Tested 1 week at 90°C in Viton® GF-200S ECO ‘poor acid condensate from ‘good samples ’ samples’ European OEM • pH of about 3 • based on mineral acids Picture of a VI sample at end of test. ECO sample had large increase in VI.

  7. Slide 7: HNBR samples in low pH acid condensate

    7 HNBR samples in low pH acid condensate Tested – 1 week at 100°C in acid condensate • pH of about 1 • based on blend of organic and mineral acids Picture of a tensile bar at end of test. Could not test sample. In same test an AEM sample performed well.

  8. Slide 8: Resistance to Acid Condensate, Engine Oils for Elastomers

    Resistance to Acid Condensate, Engine Oils for Elastomers t FKM Viton®\ Good Oil Resistance With Metal Oxides With low levels of fuel CPE and ECO ‘ Poor Acid Condensate Resistance Assumes newer engine oils: more synthetic with aggressive additive package. Elastomers with poor oil resistance, e.g. EP

  9. Slide 9: Flexible Plastics – Hytrel, Flexible Zytel: EGR Exposure

    9 Flexible Plastics – Hytrel®, Flexible Zytel®: EGR Exposure EGR liquid contact, 2000h @ 80°C

  10. Slide 10: Rigid Plastics – Zytel Grades - EGR Exposure

    10 Rigid Plastics – Zytel® Grades - EGR Exposure Reinforced materials, EGR simulation 80°C ZY 70G30HSLR BK099 200 ZY 70G35HSLRA4 BK267 Tensile strength [MPa] ZY 70G35HSLX BK357 150 ZY BM70G15HSLR BK357 ZY BM70G20HSLX BK357 100 ZY 73G30HSL BK416 ZY BM73G15THS BK317 50 ZY HTN54G35HSLR BK031 0 0 500 10

  11. Slide 11: Material Solutions – Turbo, EGR System

    11 Material Solutions – Turbo, EGR System In te gr a tio n

  12. Slide 12: Air Induction – Design Requirements

    12 Air Induction – Design Requirements Chemical Resistance (Acid, pH, fuel, oil) 1 0.8 Excellent 0.6 Good Need to Assembly Rigid 0.4 150 200 Temp, °C balance 0.2 Poor 23 -40 many Flexible 0 different minus 68 1000 factors 1 3000 5000 plus Engine Time, hours Movement 2 3 Pressure, bar

  13. Slide 13: Air ducts - Design Options

    13 Air ducts - Design Options Injection molded Welded shells 1 + rubber hoses* Blow molded 2 + rubber hoses* 3 Full integration -- All plastic or rubber * DuPont products for rubber hoses : Vamac ® , Viton ®, Nomex ®, Kevlar ®

  14. Slide 14: Typical Elastomeric Hose Constructions

    14 Typical Elastomeric Hose Constructions Up to 135°C • EPDM or ECO and Kevlar® Up to 160°C • AEM Vamac® and Kevlar®. Up to 180°C • AEM Vamac® Ultra HT and Nomex® Above 180°C • VMQ silicone rubber with Fiber – Burst strength & heat resistance Nomex® Elastomer – Chemical & heat • FKM Viton® used as i

  15. Slide 15: TC System – With Air Ducts and Hoses Highlighted

    15 TC System – With Air Ducts and Hoses Highlighted Intercooler Exhaust Fresh Air Inlet manifold EGR system PCV system Air filter Exhaust manifold Turbo charger

  16. Slide 16: Contacts

    16 Steven Mok Ed McBride Thermal Systems Technology Leader 248-459-5380 (302) 999-2153 [email protected] [email protected] Randy White Volker Plehn Air Delivery Systems Kalrez® & Vespel® 315-597-0099 1-248-583-7921 [email protected] [email protected] John Hu

DuPont — Technical Presentation (May 2011) on 6ix